Electronics Made Easy - a Complete Introduction to Electronics - Martin Denny [0]
By Martin Denny
Kindle Revision 1.0
©2010 Pixeko LLP
PASSIVE COMPONENTS
RESISTORS
Resistors as the name suggests resist the flow of electricity. When a current is passed through a resistor a voltage is developed across it. The resistance to the flow is measured in Ohms (Ω).
Resistors are produced in all sizes and can either be of a solid material or wire wound. The material chosen depends on many factors:
1) The stability with time and temperature.
2) The required power dissipation.
3) The accuracy required (the tolerance to which it can be produced).
Common materials:
1) Copper, Low resistance meter shunts
2) Metal Alloys for high resistance wire.
3) Carbon
4) Metallic Oxides.
5) Iron (used in large high power resistors)
Fixed Resistors With Power Ratings 0.25 Watts To 25 Watts.
Various Potentiometers Note High Powered Potentiometer On The Left Shows Method Of Construction.
Single Turn Open Frame, And Multiturn Trimmers.
Many resistors are identified using a colour code shown below:
Gold and silver bands are sometimes used to indicate the tolerance of High Stability resistors and generally indicate 1% and 2% respectively.
RESISTORS (Examples)
All resistance values in Ω (Ohms). K is 1000
M is 1000,000
Resistors Connected in Series
Resistors Connected in Parallel
Resistor Networks
DC Theory Examples
Ohms Law V=I*R Power Calculation P=V*I
Where:
P is power in watts ( W )
V is volts ( V )
I or i is current in Amperes ( A )
The following Symbols are used as multipliers:
K 1000 times For example mA, µA, mV, KV, etc
M 1000,000 times
m 1/1000
µ 1/1000000
DC Theory Examples
The following circuit shows a voltage divider network which feeds a
circuit with a resistance load of 1M ohm as shown below:
Capacitors
In simple terms a capacitor conducts alternating current but not direct current. Its AC resistance (reactance) is inversely proportional to frequency:
Reactance xc = 1/2πfC
Capacitors are made up of two conducting plates separated by a dielectric, as the symbol suggests, the larger the area the greater the capacitance. In some cases a thin dielectric film is coated with a layer of metal then rolled up not unlike a Swiss roll.
Electrolytic capacitors are used mainly in smoothing applications where a large capacitance is required in a small space. This is achieved due to the extreme thinness of the dielectric which is an insulating film built up by an electrolytic process on one of the electrodes. The film deposited on the electrode acts as a dielectric with a high resistance in one direction but when the polarity is reversed it presents a low resistance. Thus a voltage reversal must be avoided.
The capacitor working voltage limitation refers to the maximum peak voltage the capacitor will withstand before the dielectric breaks down.
Capacitor Types:
Electrolytic:- Polar capacitor, ie polarity sensitive. Used in applications where high values are required, at high working voltage.
Tantalum Bead:- Miniature capacitor used as a direct replacement for electrolytic capacitors in lower voltage applications (up to 35V DC).Tantalum capacitors are not available at values above 100µF.
Polyester:- These capacitors use polyester as a dielectric, they are more stable than the above capacitors but are not available above 10mF. They are not polarity sensitive and are generally used for coupling, de-coupling and less sensitive timing circuits.
Ceramic:- Ceramic capacitors have similar uses to polyester capacitors but are available at higher working voltage. Maximum value typically 0.1µF.
Polystyrene:- These capacitors use polystyrene as a dielectric, as they combine high temperature stability and high accuracy. They are used for filter and accurate timing applications but are not available above 10nF and are not used in high voltage applications.
Silvered Mica:- These capacitors have a similar specification to polystyrene but work at a higher DC voltage (500v). They are available up to 47nF. These capacitors are constructed by