An Autobiography [184]
of water that were occasionally carried along with the current of the steam, and deposited in the cylinder, where it accumulated above and below the piston, and thus produced the jerks.
In order to remove the cause of these irregularities, I placed a considerable portion of the length of the pipe which conveyed the steam from the boiler to the engine within the highly heated side flue of the boiler, so that any portion of water in the liquid form which might chance to pass along with the steam, might, ere it reached the cylinder, traverse this highly-heated steam pipe, and, in doing so, be converted into perfectly dry steam, and in that condition enter the cylinder. On carrying this simple arrangement into practice, I found the result to be in every way satisfactory. The active little steam-engine thence-forward performed its work in the most smooth and regular manner.
So far as I am aware, this early effort of mine at mechanical contrivance was the first introduction of what has since been termed "super-heated steam"--a system now extensively employed, and yielding important results, especially in the case of marine steam-engines. Without such means of supplying dry steam to the engines, the latter are specially liable to "break-downs," resulting from water, in the liquid form, passing into the cylinders along with the steam.
1828. A Method of "chucking" delicate Metal-work, in order that it may be turned with perfect truth
In fixing portions of work in the turning-lathe, one of the most important points to attend to is, that while they are held with sufficient firmness in order to be turned to the required form, they should be free from any strain which might in any way distort them. In strong and ponderous objects this can be easily accomplished by due care on the part of an intelligent workman. It is in operating by the lathe on delicate and flexible objects that the utmost care is requisite in the process of chucking, as they are easily strained out of shape by fastening them by screws and bolts, or suchlike ordinary means. This is especially the case with disc-like objects. As I had on several occasions to operate in the lathe with this class of work I contrived a method of chucking or holding them firm while receiving the required turning process, which has in all cases proved most handy and satisfactory.
This method consisted of tinning three, or, if need be, more parts of the work, and laying them down on a tinned face-plate or chuck, which had been heated so as just to cause the solder to flow. As soon as the solder is cooled and set, the chuck with its attached work may then be put in the lathe, and the work proceeded with until it is completed. By again heating the chuck, by laying upon it a piece of red-hot iron, the work, however delicate, can be simply lifted off, and will be found perfectly free from all distortion.
I have been the more particular in naming the use of three points of attachment to the chuck or face-plate, as that number is naturally free from any risk of distortion. I have on so many occasions found the great value of this simple yet most secure mode of fixing delicate work in the lathe, that I feel sure that any one able to appreciate its practical value will be highly pleased with the results of its employment.
The same means can, in many cases, be employed in fixing delicate work in the planing-machine. All that is requisite is to have a clean-planed wrought-iron or brass fixing-plate, to which the work in hand can be attached at a few suitable parts with soft solder, as in the case of the turning lathe above described.
1828. A Method of casting Specula for Reflecting Telescopes, so as to ensure perfect Freeness from Defects, at the same time enhancing the Brilliancy of the Alloy.
My father possessed a very excellent achromatic spy-glass of 2 inches diameter. The object-glass was made by the celebrated Ramsden. When I was about fifteen I used it to gaze at the moon, planets, and sun-spots. Although this instrument revealed to
In order to remove the cause of these irregularities, I placed a considerable portion of the length of the pipe which conveyed the steam from the boiler to the engine within the highly heated side flue of the boiler, so that any portion of water in the liquid form which might chance to pass along with the steam, might, ere it reached the cylinder, traverse this highly-heated steam pipe, and, in doing so, be converted into perfectly dry steam, and in that condition enter the cylinder. On carrying this simple arrangement into practice, I found the result to be in every way satisfactory. The active little steam-engine thence-forward performed its work in the most smooth and regular manner.
So far as I am aware, this early effort of mine at mechanical contrivance was the first introduction of what has since been termed "super-heated steam"--a system now extensively employed, and yielding important results, especially in the case of marine steam-engines. Without such means of supplying dry steam to the engines, the latter are specially liable to "break-downs," resulting from water, in the liquid form, passing into the cylinders along with the steam.
1828. A Method of "chucking" delicate Metal-work, in order that it may be turned with perfect truth
In fixing portions of work in the turning-lathe, one of the most important points to attend to is, that while they are held with sufficient firmness in order to be turned to the required form, they should be free from any strain which might in any way distort them. In strong and ponderous objects this can be easily accomplished by due care on the part of an intelligent workman. It is in operating by the lathe on delicate and flexible objects that the utmost care is requisite in the process of chucking, as they are easily strained out of shape by fastening them by screws and bolts, or suchlike ordinary means. This is especially the case with disc-like objects. As I had on several occasions to operate in the lathe with this class of work I contrived a method of chucking or holding them firm while receiving the required turning process, which has in all cases proved most handy and satisfactory.
This method consisted of tinning three, or, if need be, more parts of the work, and laying them down on a tinned face-plate or chuck, which had been heated so as just to cause the solder to flow. As soon as the solder is cooled and set, the chuck with its attached work may then be put in the lathe, and the work proceeded with until it is completed. By again heating the chuck, by laying upon it a piece of red-hot iron, the work, however delicate, can be simply lifted off, and will be found perfectly free from all distortion.
I have been the more particular in naming the use of three points of attachment to the chuck or face-plate, as that number is naturally free from any risk of distortion. I have on so many occasions found the great value of this simple yet most secure mode of fixing delicate work in the lathe, that I feel sure that any one able to appreciate its practical value will be highly pleased with the results of its employment.
The same means can, in many cases, be employed in fixing delicate work in the planing-machine. All that is requisite is to have a clean-planed wrought-iron or brass fixing-plate, to which the work in hand can be attached at a few suitable parts with soft solder, as in the case of the turning lathe above described.
1828. A Method of casting Specula for Reflecting Telescopes, so as to ensure perfect Freeness from Defects, at the same time enhancing the Brilliancy of the Alloy.
My father possessed a very excellent achromatic spy-glass of 2 inches diameter. The object-glass was made by the celebrated Ramsden. When I was about fifteen I used it to gaze at the moon, planets, and sun-spots. Although this instrument revealed to